מה אם הברגה של האוגן פגומה כאשר התקע מושחל מותקן בדלי הפלדה המוגמר, ולא ניתן להבריג את התקע?
Drum flange is a common closure device for tight head steel pail or steel drum. What if the flange thread was damaged due to the failure of the flange locking die, resulting in damage to the inner thread of the flange, and the plug cannot be screwed in. What should be done?
תשובה:
This situation is actually a relatively common problem in barrel-making enterprises. Under normal circumstances, problems should be discovered early in the flange locking process, and the mold or equipment should be repaired in time to avoid greater losses. When the steel drum is finished, it is found that the flange thread is damaged. It is indeed relatively late, but there are remedies. Generally, manual taps can be used to repair.
שיטת תיקון ידנית של חוט אוגן תוף פלדה
Under normal circumstances, when the thread damage is not very heavy, it is easiest to use a manual tap to repair.
I Preparation of tools
1. Purchase thread taps suitable for drum flanges. Standard closed steel drum flange, the large flange is G2 pipe thread, the small flange is G3/4 pipe thread, and taps are purchased according to the standard. The following figure shows common tap shapes. If you are not sure what kind of tap to buy, you can contact the flange supplier, and they will definitely give you the most suitable tap.
2. In addition to buying taps, you should also buy matching tap wrenches, as shown in the figure below, there are usually two types of wrenches.
3. If you use it frequently, for convenience, you can directly weld a wrench to the rear end of the tap without removing it.
II the repair method and process
תיקון החוט הוא למעשה תהליך הקשה. הברג את הברז דרך הברגה הפנימית של האוגן פעם אחת, והחלק הפגום של הברז הפנימי של האוגן יתוקן.
בעת תיקון, הברג את הברז לתוך הברגה של האוגן במומנט מסוים כדי להבריג את הברז המותאם.
איכות התיקון הידני מושפעת מאוד מגורמים אנושיים, כך שאנו יכולים להבטיח את איכות התיקון של הברגות אוגן רק על ידי נקיטת השיטה הנכונה.
1. תוף פלדה קבוע
בתהליך של תיקון חוט אוגן, תוף הפלדה נתון לכוח האנטי-, כך שאם דלי הפלדה או התוף אינם קבועים, הם עלולים להסתובב עם הברז, כך שההברגה לא יכולה להיות מְתוּקָן. לכן, לפני התיקון, יש לתקן תחילה את תוף הפלדה. בדרך כלל, שני אנשים יכולים גם לעבוד יחד לתיקון, אדם אחד אחראי להחזיק בשתי ידיו את חבית הפלדה כדי למנוע ממנה להסתובב, והאדם השני מפעיל את הברז.
2. מיקום הברז
To start the repair, keep the tap straight, then straighten the tap with one hand and lightly hinge the bar with the other hand. Observe whether the tap is perpendicular to the top surface of the barrel from the front or side. If necessary, it can be corrected with a ruler, so that the direction of the tap is basically correct. This process is very important, if the tap is not entered correctly, the result of the repair may be more damaging to the thread.
3. תיקון ברזים
אם הברז לא נמצא במצב הנכון בתחילת התיקון, ניתן לפתוח את הברז ולהחזיר אותו למצב הנכון. כאשר ראש הברז נכנס כולו לאוגן, אין עוד צורך להפעיל כוח צירי ולהסתמך על הברגה טבעית של הברגה.
4. יציבות הברז
The force should be uniform. When turning the wrench, the operator's two hands should be balanced. Do not use too much force and shake left and right, otherwise the thread profile will be easily torn, the threaded hole will be enlarged and the taper will be increased, and the tap will be broken.
5. Exit of the tap
השתמשו בראש המפתח כדי לסובב דרך כל החוטים של האוגן, כך שהברז יהיה רופף, ולאחר מכן פתחו את הברז ההפוך, כי ההתאמה בין הברז המתוקן לברז רופפת. הימנע מטלטלות ורטט של הברז בעת נסיגה, מה שעלול להרוס את גימור פני השטח של החוט.
III Matters needing attention
לאחר תיקון הברז של האוגן באמצעות ברז ידני, ייתכן שיישארו סיבי ברזל בתוך תוף הפלדה, וזה בלתי נמנע. לכן, לאחר סיום התיקון יש לנקות את סיבי הברזל בחבית בשיטה יעילה כדי להבטיח את ניקיון חבית הפלדה.
בנסיבות רגילות, הברט האוגן המתוקן יהיה רופף יותר מההברגה הרגילה כאשר תקע החבית מותקן, וזו תופעה נורמלית ואינה משפיעה על השימוש.
